BoardCanvas
Sign In
Back to Knowledge Center
Tech Spec4 min read2026-11-11

What Size Should Snowboard Topsheet Artwork Be? (By Maker)

By Ray · BoardCanvas · Specs checked against the makers' official pages

Direct Answer / Executive Summary

Snowboard topsheet artwork is always a full rectangle larger than the board, never trimmed to the board shape. By maker: Donek requires the full extent of its template rectangle; Prior requires a rectangle measuring your board length plus 6 cm by 34 cm wide; Proteus uses a 68 × 13 inch template that the artwork must fill completely, with no borders or gaps.

1. The universal rules

  • Never trim to the board shape. Donek states this explicitly: artwork must be the full extent of the outer rectangle of the template. Makers align and trim it themselves.
  • Tip at the top. Submit as a vertical rectangle with the nose up.
  • Add bleed. Your design must run past the board outline on all sides; anything exactly at the edge will shift in production.

2. Size by maker

MakerArtwork sizeNotes
DonekFull template rectangle for your boardRequest the template for your exact board specs
Prior(Board length + 6 cm) × 34 cmFor 300 DPI bitmap art
Proteus68 × 13 in templateArtwork fills the entire artboard, own layer
Vinyl wrap (e.g. Blank Snowboards method)Board length & nose/tail width + a few inches each sideCalculated from your board's spec sheet

3. The shortcut

In BoardCanvas the canvas is your exact board model and its UV template, so size and bleed are handled by construction. Export, and the file is the rectangle your maker expects.

The rectangle rule, with real numbers

Almost every maker wants a rectangle, not a board-shaped file — the graphic is printed flat, then pressed and cut to the outline, and the press needs material past every edge. The rectangle dimensions differ by maker, and getting them wrong is the most common reason artwork comes back:

MakerArtwork canvasFor a 160 cm board
PriorLength + 6 cm × 34 cm, 300 DPI166 × 34 cm (≈19,600 × 4,000 px)
DonekFull-size template, 150 DPI (JPG/TIF) or vector AI/SVGTemplate-sized (≈9,500 × 2,000 px at 150 DPI)
Proteus68″ × 13″ template172.7 × 33 cm — one size covers their range

Worked example: sizing art for a 160 cm Prior

Prior's rule is board length + 6 cm by 34 cm at 300 DPI. For a 160: the canvas is 166 × 34 cm. Convert to inches (65.4″ × 13.4″) and multiply by 300: 19,606 × 4,016 pixels. That is the file the press works from. If your source image is 4,096 px wide, it must be upscaled roughly 4.8× — possible with a good AI upscaler, but fine linework will soften; a vector file (which Donek accepts as AI/SVG) has no such ceiling. In BoardCanvas you never do this arithmetic by hand: pick the model and size, and the editor works on the true outline at print scale, then exports the full rectangle the maker asked for.

Bleed: how much margin is enough?

Bleed is artwork that extends past the cut line so press movement never exposes an unprinted edge. Prior's +6 cm length and 34 cm width (wider than any of their waists) is the bleed, built into the canvas. On a template-based route, keep backgrounds and patterns running to the template's outer edge and keep anything precious — faces, words, logos — at least 2 cm inside the outline, because the nose and tail curves eat margin as the graphic wraps. The sidecut is the sneaky part: at the waist the board can be 5–7 cm narrower than at the contact points, so a design element placed "near the edge" amid the board may end up printed off the edge entirely.

One canvas, every size? Why artwork must be re-composed per size

A model rarely comes in one length. The same name might span 148–166 cm, and the outline does not scale uniformly: waist width, sidecut depth and nose/tail proportions all shift across the run. Artwork stretched from the 166 file onto the 152 template distorts exactly where it hurts — the waist pinches the design's middle, and elements placed for the long board's nose land on the short board's inserts. This is why BoardCanvas stores the true outline per size and why the export is generated from the size you picked, not scaled from a master. If you are preparing files manually, treat each size as its own composition pass: same artwork, re-cropped and re-checked per template. It is an extra twenty minutes per size and the difference between a graphic that fits and one that merely covers.

Check your own file in ten seconds

Theory is cheap — run your actual image through the free snowboard print checker: it grades your file against Donek's 150 DPI and Prior's 300 DPI specs for your exact board size, entirely in your browser.

Sources

Create Your Custom Snowboard Deck

Apply these specs and design your unique AI graphics in 3D now.

Open 3D Customizer